Chapter  start   Previous  page  Next  page

2.6.2   Adders

We can view addition in terms of generate , G[ i ], and propagate , P[ i ], signals.

  method 1  method 2

  G[ i ] = A[ i ] · B[ i ]  G[ i ] = A[ i ] · B[ i ](2.42)

  P[ i ] = A[ i ]   B[ i ]  P[ i ] = A[ i ] + B[ i ](2.43)

  C[ i ] = G[ i ] + P[ i ] · C[ i   1]  C[ i ] = G[ i ] + P[ i ] · C[ i   1](2.44)

  S[ i ] = P[ i ]   C[ i   1]  S[ i ] =  A[ i ]   B[ i ]   C[ i   1](2.45)

where C[ i ] is the carry-out signal from stage i , equal to the carry in of stage ( i  + 1). Thus, C[ i ] = COUT[ i ] = CIN[ i  + 1]. We need to be careful because C[0] might represent either the carry in or the carry out of the LSB stage. For an adder we set the carry in to the first stage (stage zero), C[1] or CIN[0], to '0'. Some people use delete (D) or kill (K) in various ways for the complements of G[i] and P[i], but unfortunately others use C for COUT and D for CINso I avoid using any of these. Do not confuse the two different methods (both of which are used) in Eqs.  2.422.45 when forming the sum, since the propagate signal, P[ i ] , is different for each method.

Figure 2.22(a) shows a conventional RCA. The delay of an n -bit RCA is proportional to n and is limited by the propagation of the carry signal through all of the stages. We can reduce delay by using pairs of "go-faster" bubbles to change AND and OR gates to fast two-input NAND gates as shown in Figure 2.22(a). Alternatively, we can write the equations for the carry signal in two different ways:

  either  C[ i ] = A[ i ] · B[ i ] + P[ i ] · C[ i   1](2.46)

  orn  C[ i ] = (A[ i ] + B[ i ] ) · (P[ i ]' + C[ i   1]),(2.47)

where P[ i ]'  = NOT(P[ i ]). Equations 2.46 and 2.47 allow us to build the carry chain from two-input NAND gates, one per cell, using different logic in even and odd stages (Figure 2.22b):

  even stages  odd stages

  C1[ i ]' = P[ i  ] · C3[ i   1] · C4[ i   1]  C3[ i ]' = P[ i  ] · C1[ i   1] · C2[ i   1](2.48)

  C2[ i ] = A[ i  ] + B[ i  ]  C4[ i ]' = A[ i  ] · B[ i  ](2.49)

  C[ i ] = C1[ i  ] · C2[ i  ]  C[ i ] = C3[ i  ] ' + C4[ i  ]'(2.50)

 

FIGURE 2.22  The ripple-carry adder (RCA). (a) A conventional RCA. The delay may be reduced slightly by adding pairs of bubbles as shown to use two-input NAND gates. (b) An alternative RCA circuit topology using different cells for odd and even stages and an extra connection between cells. The carry chain is a fast string of NAND gates (shown in bold).

(the carry inputs to stage zero are C3[1] = C4[1] = '0'). We can use the RCA of Figure 2.22(b) in a datapath, with standard cells, or on a gate array.

Instead of propagating the carries through each stage of an RCA, Figure 2.23 shows a different approach. A carry-save adder ( CSA ) cell CSA(A1[ i ], A2[ i ], A3[ i  ], CIN, S1[ i ], S2[ i ], COUT) has three outputs:




© 2024 Internet Business Systems, Inc.
670 Aberdeen Way, Milpitas, CA 95035
+1 (408) 882-6554 — Contact Us, or visit our other sites:
AECCafe - Architectural Design and Engineering EDACafe - Electronic Design Automation TechJobsCafe - Technical Jobs and Resumes  MCADCafe - Mechanical Design and Engineering ShareCG - Share Computer Graphic (CG) Animation, 3D Art and 3D Models
  Privacy PolicyAdvertise